CCNA, CCENT, CCNP Test' Tips Greensboro NC

This article lists some questions on static routing, the OSI model, IP version 6, and other topics to make you victory in CCNA, CCENT, and CCNP certification exam.

Local Companies

Dew K Michie Harriss Ph.D.
336-272-0855
806 Green Valley Rd
Greensboro, NC
Joyce Richman & Associates LTD
336-288-1799
2911 Shady Lawn Dr
Greensboro, NC
Career Development Consultants
336-854-9393
1209 Westminster DR
Greensboro, NC
Spherion
(336) 854-5579
629 Green Valley Rd Ste 202
Greensboro, NC
Spherion
(336) 856-0044
4212B W Wendover Ave
Greensboro, NC
Officeteam
(336) 668-0766
101 Centreport Dr
Greensboro, NC
C S R Medical
(336) 856-1825
3409 W Wendover Ave
Greensboro, NC
Kelly Services
(336) 854-1353
620 Green Valley Rd
Greensboro, NC
Randstad
(336) 294-7674
3410 W Wendover Ave Ste B
Greensboro, NC
Agency Inc the
(336) 272-8447
1301 Carolina St
Greensboro, NC

Here are some questions on static routing, the OSI model, IP version 6, and other topics to help prepare you for CCNA, CCENT, and CCNP certification exam success! Network+ candidates, I didn’t leave you out!

CCNA Certification:

What character or combination of characters indicates a statically configured default route?

Answer: An "S*" next to a route indicates that it is a default static route. If there were no asterisk, the route type indicated would be a static route – but not a default static route.

CCENT Certification / Network+ Certification Question:

Which one of the following networking terms is not associated with the same OSI layer as the others?

A. router

B. packet

C. TCP

D. IP

Answer: C. TCP runs at the Transport layer of the OSI model. The other three terms are associated with the Network layer. The Network layer is sometimes referred to as the “routing layer”.

CCNP Certification / BSCI Exam:

If an IPv6 address begins with "FF", what kind of address is it?

A. broadcast

B. unicast

C. anycast

D. multicast

Answer: D. Any IPv6 address beginning with "FF" is a multicast. IPv6 does not use broadcasts.

CCNP Certification / BCMSN Exam:

You've configured an Etherchannel and note that the trunk has gone down. You check the interfaces on one switch and note that two are "err-disabled". The corresponding ports on the other switch are not. What should you do?

A. Nothing - that's the normal and desired behavior.

B. Shut and reopen the err-disabled interfaces.

C. Shut and reopen the non-err-disabled interfaces.

D. Use the err-abled command on the err-disabled interfaces.

Answer: B. After finishing the config, shut and reopen the err-disabled interfaces. If the configuration is correct, that will do the trick. This is common when you configure all of the ports on one switch and then start configuring the other switch, rather than going back and forth between the appropriate ports on the switches.

See you soon with more CCNA, Network+, CCNP, and CCENT questions!

About the Author:

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (http://www.thebryantadvantage.com ), home of free CCNA and CCNP tutorials, and The Ultimate CCNA and CCNP Study Packages.

For free daily CCNA, CCNP, CCENT, Network+, Security+, and A+ questions, just visit the website and sign up for the daily newsletter!

Article Source: thePhantomWriters Article Submission Service

Featured Local Company

Dew K Michie Harriss Ph.D.

336-272-0855
806 Green Valley Rd
Greensboro, NC