CCNA, CCENT, CCNP Test' Tips Honolulu HI

This article lists some questions on static routing, the OSI model, IP version 6, and other topics to make you victory in CCNA, CCENT, and CCNP certification exam.

Local Companies

Vocational Management Consultants
(808) 538-8733
715 S King Suite 410
Honolulu, HI
Worknet Inc
(808) 941-7771
1020 Isenberg St
Honolulu, HI
Workability
(808) 536-9977
1520 Liliha St
Honolulu, HI
Employment Specialists
(808) 528-1550
1164 Bishop St Ste 1007
Honolulu, HI
Kelly Services
(808) 536-9343
1100 Ward Ave Ste 1020
Honolulu, HI
Beneficial Employment Services Inc
(808) 526-4121
841 Bishop St Ste 904
Honolulu, HI
Dunhill Professional Staffing of Hawaii
(808) 524-2550
Honolulu, HI
Island Wide Staffing
(808) 396-7000
Honolulu, HI
Manpower
(808) 524-3630
737 Bishop St Ste 1880
Honolulu, HI
Olympia Personnel
(808) 597-8555
1314 S King St Ste 1255
Honolulu, HI

Here are some questions on static routing, the OSI model, IP version 6, and other topics to help prepare you for CCNA, CCENT, and CCNP certification exam success! Network+ candidates, I didn’t leave you out!

CCNA Certification:

What character or combination of characters indicates a statically configured default route?

Answer: An "S*" next to a route indicates that it is a default static route. If there were no asterisk, the route type indicated would be a static route – but not a default static route.

CCENT Certification / Network+ Certification Question:

Which one of the following networking terms is not associated with the same OSI layer as the others?

A. router

B. packet

C. TCP

D. IP

Answer: C. TCP runs at the Transport layer of the OSI model. The other three terms are associated with the Network layer. The Network layer is sometimes referred to as the “routing layer”.

CCNP Certification / BSCI Exam:

If an IPv6 address begins with "FF", what kind of address is it?

A. broadcast

B. unicast

C. anycast

D. multicast

Answer: D. Any IPv6 address beginning with "FF" is a multicast. IPv6 does not use broadcasts.

CCNP Certification / BCMSN Exam:

You've configured an Etherchannel and note that the trunk has gone down. You check the interfaces on one switch and note that two are "err-disabled". The corresponding ports on the other switch are not. What should you do?

A. Nothing - that's the normal and desired behavior.

B. Shut and reopen the err-disabled interfaces.

C. Shut and reopen the non-err-disabled interfaces.

D. Use the err-abled command on the err-disabled interfaces.

Answer: B. After finishing the config, shut and reopen the err-disabled interfaces. If the configuration is correct, that will do the trick. This is common when you configure all of the ports on one switch and then start configuring the other switch, rather than going back and forth between the appropriate ports on the switches.

See you soon with more CCNA, Network+, CCNP, and CCENT questions!

About the Author:

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (http://www.thebryantadvantage.com ), home of free CCNA and CCNP tutorials, and The Ultimate CCNA and CCNP Study Packages.

For free daily CCNA, CCNP, CCENT, Network+, Security+, and A+ questions, just visit the website and sign up for the daily newsletter!

Article Source: thePhantomWriters Article Submission Service

Featured Local Company

Vocational Management Consultants

(808) 538-8733
715 S King Suite 410
Honolulu, HI