CCNA, CCENT, CCNP Test' Tips Milwaukee WI

This article lists some questions on static routing, the OSI model, IP version 6, and other topics to make you victory in CCNA, CCENT, and CCNP certification exam.

Local Companies

MCFI Employment Services
414-937-2034
2020 W Wells St
Milwaukee, WI
Abundant Life Ministry
414-962-3200
1904 E Belleview Pl
Milwaukee, WI
Voccupational Choice
414-962-6545
5225 N Ironwood Rd
Milwaukee, WI
Westaff
(414) 258-7225
2645 N Mayfair Rd Ste 210
Milwaukee, WI
Infostaff
(414) 906-0548
Milwaukee, WI
Adecco Employment Services
(414) 278-7900
330 E Kilbourn Ave
Milwaukee, WI
Wisconsin Job Centers
(414) 374-1800
1915 N Dr Martin Luther Kin
Milwaukee, WI
Financial Headhunters Inc
(262) 821-3555
Milwaukee, WI
Succeedia Inc
(414) 765-1135
930 E Knapp St
Milwaukee, WI
Y W Villages
(414) 374-1800
1915 N Dr Martin Luther Kin
Milwaukee, WI

Here are some questions on static routing, the OSI model, IP version 6, and other topics to help prepare you for CCNA, CCENT, and CCNP certification exam success! Network+ candidates, I didn’t leave you out!

CCNA Certification:

What character or combination of characters indicates a statically configured default route?

Answer: An "S*" next to a route indicates that it is a default static route. If there were no asterisk, the route type indicated would be a static route – but not a default static route.

CCENT Certification / Network+ Certification Question:

Which one of the following networking terms is not associated with the same OSI layer as the others?

A. router

B. packet

C. TCP

D. IP

Answer: C. TCP runs at the Transport layer of the OSI model. The other three terms are associated with the Network layer. The Network layer is sometimes referred to as the “routing layer”.

CCNP Certification / BSCI Exam:

If an IPv6 address begins with "FF", what kind of address is it?

A. broadcast

B. unicast

C. anycast

D. multicast

Answer: D. Any IPv6 address beginning with "FF" is a multicast. IPv6 does not use broadcasts.

CCNP Certification / BCMSN Exam:

You've configured an Etherchannel and note that the trunk has gone down. You check the interfaces on one switch and note that two are "err-disabled". The corresponding ports on the other switch are not. What should you do?

A. Nothing - that's the normal and desired behavior.

B. Shut and reopen the err-disabled interfaces.

C. Shut and reopen the non-err-disabled interfaces.

D. Use the err-abled command on the err-disabled interfaces.

Answer: B. After finishing the config, shut and reopen the err-disabled interfaces. If the configuration is correct, that will do the trick. This is common when you configure all of the ports on one switch and then start configuring the other switch, rather than going back and forth between the appropriate ports on the switches.

See you soon with more CCNA, Network+, CCNP, and CCENT questions!

About the Author:

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (http://www.thebryantadvantage.com ), home of free CCNA and CCNP tutorials, and The Ultimate CCNA and CCNP Study Packages.

For free daily CCNA, CCNP, CCENT, Network+, Security+, and A+ questions, just visit the website and sign up for the daily newsletter!

Article Source: thePhantomWriters Article Submission Service

Featured Local Company

MCFI Employment Services

414-937-2034
2020 W Wells St
Milwaukee, WI
http://www.mcfi.net