CCNA, CCENT, CCNP Test' Tips Pittsburgh PA

This article lists some questions on static routing, the OSI model, IP version 6, and other topics to make you victory in CCNA, CCENT, and CCNP certification exam.

Local Companies

Three Rivers Career Management
412- 261-6166
707 Grant St
Pittsburgh, PA
Career Development Center
412- 422-5627
5743 Bartlett St
Pittsburgh, PA
Carlino Janice L
412- 521-5530
5725 Forward Ave
Pittsburgh, PA
Litzinger Career Consulting
412- 242-5342
7625 W Hutchinson Ave
Pittsburgh, PA
Pittsburgh Staffing
(412) 471-1080
239 4th Ave
Pittsburgh, PA
Elite People Inc
(412) 288-6080
355 5th Ave
Pittsburgh, PA
Labor Ready
(412) 321-9877
1318 Western Ave
Pittsburgh, PA
Daniel Stern & Associates
(412) 244-6434
10 Duff Rd Ste 215
Pittsburgh, PA
Acba Legal Placement Service
(412) 261-0744
Koppers
Pittsburgh, PA
Kerr Dan & Associates
(412) 492-0300
344 Goldsmith Rd
Pittsburgh, PA

Here are some questions on static routing, the OSI model, IP version 6, and other topics to help prepare you for CCNA, CCENT, and CCNP certification exam success! Network+ candidates, I didn’t leave you out!

CCNA Certification:

What character or combination of characters indicates a statically configured default route?

Answer: An "S*" next to a route indicates that it is a default static route. If there were no asterisk, the route type indicated would be a static route – but not a default static route.

CCENT Certification / Network+ Certification Question:

Which one of the following networking terms is not associated with the same OSI layer as the others?

A. router

B. packet

C. TCP

D. IP

Answer: C. TCP runs at the Transport layer of the OSI model. The other three terms are associated with the Network layer. The Network layer is sometimes referred to as the “routing layer”.

CCNP Certification / BSCI Exam:

If an IPv6 address begins with "FF", what kind of address is it?

A. broadcast

B. unicast

C. anycast

D. multicast

Answer: D. Any IPv6 address beginning with "FF" is a multicast. IPv6 does not use broadcasts.

CCNP Certification / BCMSN Exam:

You've configured an Etherchannel and note that the trunk has gone down. You check the interfaces on one switch and note that two are "err-disabled". The corresponding ports on the other switch are not. What should you do?

A. Nothing - that's the normal and desired behavior.

B. Shut and reopen the err-disabled interfaces.

C. Shut and reopen the non-err-disabled interfaces.

D. Use the err-abled command on the err-disabled interfaces.

Answer: B. After finishing the config, shut and reopen the err-disabled interfaces. If the configuration is correct, that will do the trick. This is common when you configure all of the ports on one switch and then start configuring the other switch, rather than going back and forth between the appropriate ports on the switches.

See you soon with more CCNA, Network+, CCNP, and CCENT questions!

About the Author:

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (http://www.thebryantadvantage.com ), home of free CCNA and CCNP tutorials, and The Ultimate CCNA and CCNP Study Packages.

For free daily CCNA, CCNP, CCENT, Network+, Security+, and A+ questions, just visit the website and sign up for the daily newsletter!

Article Source: thePhantomWriters Article Submission Service

Featured Local Company

Three Rivers Career Management

412- 261-6166
707 Grant St
Pittsburgh, PA

Related Local Event
The Pocket MBA for Lawyers: Everything You Need to Know About Finance 2009
Dates: 7/30/2009 - 7/30/2009
Location: PBI Professional Development Conference Center
Pittsburgh, PA
View Details