CCNA, CCENT, CCNP Test' Tips Wichita KS

This article lists some questions on static routing, the OSI model, IP version 6, and other topics to make you victory in CCNA, CCENT, and CCNP certification exam.

Local Companies

Blasi Don Thomas
(316) 684-2422
641 S Hillside St
Wichita, KS
Right Management
(316) 681-8037
111 S Whittier St
Wichita, KS
Tad Technical
(316) 945-4291
650 S Westdale Dr Ste 204
Wichita, KS
Advanced Personnel
(316) 691-8998
902 S Oliver St
Wichita, KS
Personnel Services Inc
(316) 264-1515
Wichita, KS
Kansas Air National Guard Recruiting
(316) 688-0825
4100 E Harry St
Wichita, KS
Apprentice Personnel Inc
(316) 267-4781
800 S Broadway St Ste 100
Wichita, KS
Kelly Services
(316) 267-2885
727 N Waco Ave Ste 220
Wichita, KS
Preferred Personnel
(316) 263-5627
141 S Hydraulic St
Wichita, KS
Oasis Staffing
(316) 262-8222
Wichita, KS

Here are some questions on static routing, the OSI model, IP version 6, and other topics to help prepare you for CCNA, CCENT, and CCNP certification exam success! Network+ candidates, I didn’t leave you out!

CCNA Certification:

What character or combination of characters indicates a statically configured default route?

Answer: An "S*" next to a route indicates that it is a default static route. If there were no asterisk, the route type indicated would be a static route – but not a default static route.

CCENT Certification / Network+ Certification Question:

Which one of the following networking terms is not associated with the same OSI layer as the others?

A. router

B. packet

C. TCP

D. IP

Answer: C. TCP runs at the Transport layer of the OSI model. The other three terms are associated with the Network layer. The Network layer is sometimes referred to as the “routing layer”.

CCNP Certification / BSCI Exam:

If an IPv6 address begins with "FF", what kind of address is it?

A. broadcast

B. unicast

C. anycast

D. multicast

Answer: D. Any IPv6 address beginning with "FF" is a multicast. IPv6 does not use broadcasts.

CCNP Certification / BCMSN Exam:

You've configured an Etherchannel and note that the trunk has gone down. You check the interfaces on one switch and note that two are "err-disabled". The corresponding ports on the other switch are not. What should you do?

A. Nothing - that's the normal and desired behavior.

B. Shut and reopen the err-disabled interfaces.

C. Shut and reopen the non-err-disabled interfaces.

D. Use the err-abled command on the err-disabled interfaces.

Answer: B. After finishing the config, shut and reopen the err-disabled interfaces. If the configuration is correct, that will do the trick. This is common when you configure all of the ports on one switch and then start configuring the other switch, rather than going back and forth between the appropriate ports on the switches.

See you soon with more CCNA, Network+, CCNP, and CCENT questions!

About the Author:

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (http://www.thebryantadvantage.com ), home of free CCNA and CCNP tutorials, and The Ultimate CCNA and CCNP Study Packages.

For free daily CCNA, CCNP, CCENT, Network+, Security+, and A+ questions, just visit the website and sign up for the daily newsletter!

Article Source: thePhantomWriters Article Submission Service

Featured Local Company

Blasi Don Thomas

(316) 684-2422
641 S Hillside St
Wichita, KS