CMOS 555 Timer Drive Seattle WA

The following article discusses the CMOS 555, which is a drive that can run multiple LEDs from one NiHM.

Local Companies

LMN Architects
(206) 682-3460
801 2nd Ave., Ste. 501
Seattle, WA
Ruffcorn Mott Hinthorne Stine
(206) 405-4443
810 3rd Ave., Ste. 220
Seattle, WA
SRG Partnership, Inc.
(206) 973-1700
101 Yesler Way, Ste. 200
Seattle, WA
atelierjones llc
(206) 624-9966
911 Western Ave., Ste. 440
Seattle, WA
CollinsWoerman
(206) 245-2100
710 2nd Ave., Ste. 1400
Seattle, WA
INTEGRUS Architecture
(206) 628-3137
117 S Main St., Ste. 100
Seattle, WA
Zimmer Gunsul Frasca Architects LLP
(206) 623-9414
925 4th Ave., Ste. 2400
Seattle, WA
DLR Group
(206) 461-6000
901 5th Ave., Ste. 700
Seattle, WA
Sclater Partners Architects, PC
(206) 624-8682
414 Olive Way, Ste. 300
Seattle, WA
AIA Seattle
(206) 448-4938
1911 1st Ave.
Seattle, WA

provided by: EDN

Using a CMOS 555 timer and a single NPN transistor, you can drive as many as seven LEDs using a minimal amount of voltage and power from a single NiMH (nickel-metal-hydride) AA cell. The circuit works by creating much higher-voltage pulses than the voltage for powering the circuit by pulsing a high-Q power inductor. The circuit creates voltage pulses of 23V using a 1.25V NiMH cell with seven connected LEDs.

The circuit uses a CMOS timer because it functions on low voltages-in this case, as low as 1V. A single white LED rated at 9300 mcd maintains its brilliance down to this low voltage. The circuit works for 192 hours using a 2000-mAHr-rated NiMH cell. The output of the timer is a 4.5-µsec pulse repeating at a 222-kHz rate. Although you can use the circuit to power any LED, it works best using high-brightness, high-power LEDs rated at 3000 mcd or higher. Obviously, the higher the millicandela rating, the brighter the LED will appear.

You can connect the LEDs in parallel if their forward voltages match; otherwise, the LED with the lowest forward voltage will dim out the other LEDs. Using the parallel connection, all LEDs will glow with equal brightness if their forward voltages match. Adding LEDs does not increase the current drawn from the battery but reduces the brilliance of all of the connected LEDs.

The advantage of connecting the LEDs in series-which is possible because of the high pulse voltage they produce-is equal brilliance of all LEDs, regardless of their individual forward-voltage drops and millicandela ratings. Each additional LED decreases additional voltage and lowers the resulting current into the series string of LEDs, lowering their brilliance. Using seven LEDs with a single 1.25V cell draws a current of only 8 mA. By adding a 1.25V cell to the power input, the LEDs become so brilliant that it is difficult to look at them. With a 2.5V supply, the peak voltage pulses increase to 70V with no connected LEDs. With the LEDs connected, the output voltage peaks at 25V. Current draw at 2.5V is 20 mA.



author: Chuck Irwin, Hendersonville, NC

EDN. Copyright © 2008 Reed Business Information, a division of Reed Elsevier Inc. All rights reserved.

Featured Local Company

LMN Architects

(206) 682-3460
801 2nd Ave., Ste. 501
Seattle, WA
http://www.lmnarchitects.com/index.asp

Related Local Events
ASLA - American Society of Landscape Architects - Annual Meeting & Expo
Dates: 9/30/2011 - 10/4/2011
Location: Washington State Convention and Trade Center
Seattle, WA
View Details

Kirkland Concours d’Elegance
Dates: 9/13/2009 - 9/13/2009
Location: Carillon Point
Kirkland, WA
View Details

International Conference on Superplasticity in Advanced Materials (ICSAM 2009)
Dates: 6/29/2009 - 7/2/2009
Location: Bell Harbor Conference Center
Seattle, WA
View Details

AACE - Association for the Advancement of Cost Engineering International's 53rd Annual Meeting
Dates: 6/28/2009 - 7/1/2009
Location: Sheraton Seattle Hotel
Seattle, WA
View Details