Molded Plastics With Extended And Enhanced Mold Ability Nashville TN

New applications debut for thermoplastic elastomer and PEEK

Local Companies

Scott Carleen Equipment Leasing Services
(615) 399-9183
Nashville, TN
Rainbow Rentals
(615) 356-4100
5815 Charlotte Pike
Nashville, TN
Rent-A-Center
(615) 367-9221
1128 Murfreesboro Pike
Nashville, TN
Tennessee Rentals Llc
(615) 889-8845
209 River Hills Dr
Nashville, TN
Home Depot the
(615) 860-1651
1584 Gallatin Ave
Nashville, TN
Budget Truck Rental
(615) 361-3100
1058 Murfreesboro Pike
Nashville, TN
Home Depot the
(615) 662-4400
7665 Highway 70 S
Nashville, TN
Sunbelt Rentals Inc
(615) 868-0623
1201 Northgate Business
Nashville, TN
Budget Truck Rental
(615) 254-4131
25th & Clarksville H
Nashville, TN
Rent-A-Center
(615) 383-7368
5402 Charlotte Ave
Nashville, TN

provided by: Design News

Applications of molded plastics continue to extend due to enhanced properties and moldability. New glass microspheres are 40 percent stronger, even though only half the size of previous versions of the product. The glass bubbles can be used, where suitable, to replace glass fiber or fillers and at the same time improve the rheology of the plastic compound. Also worth noting is an important new aircraft application for a high-temperature plastic that replaces aluminum, as the plastics assault on metals continues in the battle to lightweight aircraft.

Peek PerformanceDoug Smock

Weight played a major factor replacing aluminum with a polyetheretherketone (PEEK) for the hubcaps enclosing a new tire pressure monitoring system for the landing gear of the Boeing 777. "By specifying Victrex PEEK polymer, each hubcap now weighs less than 7 kg (1.5 lb)," says Jeff Tonn, design engineer at Crane Aerospace & Electronics of Lynnwood, WA. "With 14 wheels per plane, the weight reduction is considerable." The tire monitoring system on the Boeing 777 is designed to assure proper tire air pressure for take-off and landing. The hubcaps include a conduit which allows a rim-mounted pressure sensor to communicate with an onboard system providing real-time data to the cockpit. http://rbi.ims.ca/5697-588

Tiny Glass BubblesDoug Smock

Tiny glass microspheres act like ball bearings, improving the flowability of plastic compounds and allowing more complex parts to be produced. The new 3M Performance Additive iM30K is the first hollow glass microsphere in 3M's line of glass bubbles that can withstand higher pressures involved in thermoplastic compounding, injection molding and extrusion processes in the plastics industry. The new microsphere of borosilicate glass is water insoluble, chemically stable and low on alkalis. It is 40 percent stronger than 3M's previous leading high-strength glass microspheres while being only half their size at a diameter of just 17 ?m (D50). The isostatic crush strength of the new microsphere is 2,000 bar (200 MPa). http://rbi.ims.ca/5697-587

Overmolded Cowl VentsDoug Smock

A thermoplastic elastomer is used for the cowl vent seals on two series of Peugeot automobiles because of its unusual combination of rubber-like mechanical properties and weathering resistance. Situated between the windshield and the engine compartment and spanning the width of the vehicle, the cowl vent permits fresh air to pass from the outside to the interior. For the Peugeot 207 and 307 series cars, sealing lips of Tekron TPE that are up to 1.5m (nearly 5 ft) long are overmolded onto cowl vent substrates of glass-reinforced polypropylene (PP). The over-molding is part of a single molding cycle for a three-component part that includes the structural PP substrate, the Tekron sealing lip and a molded-in view port which enables the chassis number of the vehicle to be visible. http://rbi.ims.ca/5697-589



author: By Doug Smock, Contributing Editor, Materials and Fastening

Design News. Copyright © 2008 Reed Business Information, a division of Reed Elsevier Inc. All rights reserved.

Featured Local Company

Thompson Machinery

(931) 552-5496
541 Alfred Thun Rd
Clarksville, TN
http://www.thompsonmachinery.com