Molded Plastics With Extended And Enhanced Mold Ability Oakland CA

New applications debut for thermoplastic elastomer and PEEK

Local Companies

Tidewater Sand & Gravel Inc
(800) 626-6250
4501 Tidewater Ave
Oakland, CA
Berkeley Equipment Rentals
(510) 845-6797
2969 Macarthur Blvd
Oakland, CA
Vortex Marine Construction
(510) 261-2400
1904 Franklin St
Oakland, CA
Equipment Appraisers LLC
(510) 233-3000
1587 Franklin St
Oakland, CA
Segale Bros Wood Products Inc
(510) 652-8113
2101 Webster St
Oakland, CA
Cresco Equipment Rentals
(510) 601-6480
6767 Broadway Ter
Oakland, CA
Quality Construction Inc
(510) 763-5082
247 10th St
Oakland, CA
Wacker Construction Equipment
(510) 893-3690
909 7th St
Oakland, CA
Hertz Corp
(510) 729-7222
7727 Oakport St
Oakland, CA
Quality Construction Supply
(510) 832-2996
740 Julie Ann Way
Oakland, CA

provided by: Design News

Applications of molded plastics continue to extend due to enhanced properties and moldability. New glass microspheres are 40 percent stronger, even though only half the size of previous versions of the product. The glass bubbles can be used, where suitable, to replace glass fiber or fillers and at the same time improve the rheology of the plastic compound. Also worth noting is an important new aircraft application for a high-temperature plastic that replaces aluminum, as the plastics assault on metals continues in the battle to lightweight aircraft.

Peek PerformanceDoug Smock

Weight played a major factor replacing aluminum with a polyetheretherketone (PEEK) for the hubcaps enclosing a new tire pressure monitoring system for the landing gear of the Boeing 777. "By specifying Victrex PEEK polymer, each hubcap now weighs less than 7 kg (1.5 lb)," says Jeff Tonn, design engineer at Crane Aerospace & Electronics of Lynnwood, WA. "With 14 wheels per plane, the weight reduction is considerable." The tire monitoring system on the Boeing 777 is designed to assure proper tire air pressure for take-off and landing. The hubcaps include a conduit which allows a rim-mounted pressure sensor to communicate with an onboard system providing real-time data to the cockpit. http://rbi.ims.ca/5697-588

Tiny Glass BubblesDoug Smock

Tiny glass microspheres act like ball bearings, improving the flowability of plastic compounds and allowing more complex parts to be produced. The new 3M Performance Additive iM30K is the first hollow glass microsphere in 3M's line of glass bubbles that can withstand higher pressures involved in thermoplastic compounding, injection molding and extrusion processes in the plastics industry. The new microsphere of borosilicate glass is water insoluble, chemically stable and low on alkalis. It is 40 percent stronger than 3M's previous leading high-strength glass microspheres while being only half their size at a diameter of just 17 ?m (D50). The isostatic crush strength of the new microsphere is 2,000 bar (200 MPa). http://rbi.ims.ca/5697-587

Overmolded Cowl VentsDoug Smock

A thermoplastic elastomer is used for the cowl vent seals on two series of Peugeot automobiles because of its unusual combination of rubber-like mechanical properties and weathering resistance. Situated between the windshield and the engine compartment and spanning the width of the vehicle, the cowl vent permits fresh air to pass from the outside to the interior. For the Peugeot 207 and 307 series cars, sealing lips of Tekron TPE that are up to 1.5m (nearly 5 ft) long are overmolded onto cowl vent substrates of glass-reinforced polypropylene (PP). The over-molding is part of a single molding cycle for a three-component part that includes the structural PP substrate, the Tekron sealing lip and a molded-in view port which enables the chassis number of the vehicle to be visible. http://rbi.ims.ca/5697-589



author: By Doug Smock, Contributing Editor, Materials and Fastening

Design News. Copyright © 2008 Reed Business Information, a division of Reed Elsevier Inc. All rights reserved.

Featured Local Company

Tidewater Sand & Gravel Inc

(800) 626-6250
4501 Tidewater Ave
Oakland, CA

Related Local Events
Business Issues Committee Meeting
Dates: 6/26/2009 - 6/26/2009
Location: Fairfield-Suisun Chamber of Commerce
Fairfield, CA
View Details

Executive Board Meeting
Dates: 6/23/2009 - 6/23/2009
Location: Fairfield-Suisun Chamber of Commerce
Fairfield, CA
View Details

Membership Committee Meeting
Dates: 6/18/2009 - 6/18/2009
Location: Fairfield-Suisun Chamber of Commerce
Fairfield, CA
View Details

Suisun City Business Group Meeting
Dates: 6/18/2009 - 6/18/2009
Location: Suisun City Council Chambers
Suisun, CA
View Details

Travis Regional Armed Forces Committee Meeting
Dates: 6/15/2009 - 6/15/2009
Location: Delta Breeze Club, Travis AFB
Travis AFB, CA
View Details